Anleitungen und Treiber zur TwiSTEr 1040 STE Kombikarte
Antworten
Gaga
Beiträge: 23
Registriert: 21. Sep 2022, 20:32

ROMSELECT + INT

Beitrag von Gaga » 23. Okt 2022, 10:01

Die Benutzung von ROMSELECT ist denkbar einfach:
Stelle eine steckbare Kabelverbindung (hier orange) her zwischen dem mittleren Mainboard-Pin von W102 und dem schwarzen oder roten Pin des TwiSTEr.

Die Verbindung zum mittleren Mainboard-Pin von W102 bleibt immer so. Wenn das andere Ende des orangenen Kabels an 5V gesteckt wird (auf dem Twister oder anderer Stelle), dann ist das FlashROM auf dem Twister aktiv. Wird das Kabelende hingegen an einen Massekontakt gesteckt, dann ist das ROM auf dem Mainboard aktiv. Letztere Auswahl ist immer dann erforderlich, wenn es einen Fehler beim beschreiben des Flashroms gegeben haben sollte.

Achtung: diese Umschaltung funktioniert nur, wenn auf dem Mainboard ein TOS 2.06 oder EmuTOS in zwei 32poligen ROMs ist. Sofern auf dem STE Mainboard noch das originale TOS 1.06/1.62 in zwei 28poligen ROMs ist, funktioniert die Umschaltung mittels Kabel nicht und die originalen ROMS solten entfernt oder gegen 32polige ROMs ausgetaucht werden.

Für eine Umbauanleitung des STE auf TOS 2.06 siehe hier:
https://wiki.newtosworld.de//index.php? ... alten_Roms

Auch die Installation des Kabels (hier hellgrau) für das INT Signal ist sehr einfach:
Stelle eine Verbindung her zwischen dem unteren Pins von CON1 auf dem Twister (steckbar) und Pin10 des nach extern führenden ACSI Ports (ganz rechter Kontakt) oder alternativ am unteren Kontakt des Widerstandes R421. Es empfiehlt sich, dies fest anzulöten.

_____________________


The use of ROMSELECT is very simple:
Establish a pluggable cable connection (orange here) between the centre mainboard pin of W102 and the black or red pin of the TwiSTEr.

The connection to the centre mainboard pin of W102 always remains the same. If the other end of the orange cable is connected to 5V (on the Twister or elsewhere), the FlashROM on the Twister is active. If, on the other hand, the end of the cable is connected to a ground contact, the ROM on the mainboard is active. The latter selection is always required if there is an error when writing to the FlashROM.

Attention: This switch only works if there is a TOS 2.06 or EmuTOS in two 32-pin ROMs on the mainboard. If the original TOS 1.06/1.62 in two 28-pin ROMs is still on the STE mainboard, the switchover via cable will not work and the original ROMs should be removed or replaced with 32-pin ROMs.

For instructions on converting the STE to TOS 2.06, see here:
https://wiki.newtosworld.de//index.php? ... alten_Roms

The installation of the cable (here light grey) for the INT signal is also very simple:
Make a connection between the lower pins of CON1 on the Twister (pluggable) and pin10 of the ACSI port leading to the outside (rightmost contact) or alternatively at the lower contact of resistor R421. It is recommended to solder this firmly.
Dateianhänge
INT alternate Solder point
INT alternate Solder point
INT and ROMSELECT cables
INT and ROMSELECT cables
general info
general info
Centerpin of W102
Centerpin of W102

Antworten